Dynamic Stress and Strain Analysis for 8×4 Truck Frame

<- Back to II. Mechanical Engineering & Physics Vol.4

Cite the paper

Abdel-halim, Nagwa Ahmed

Dynamic Stress and Strain Analysis for 8x4 Truck Frame Journal Article

Mechanics, Materials Science & Engineering, 4 , pp. 96-109, 2016, ISSN: 2412-5954.

Abstract | Links | BibTeX

Authors: Nagwa Ahmed Abdel-halim

ABSTRACT. The truck chassis is subjected to lower stresses in rest than it is in movement where the stresses and strains are considerably increased. The current work contains the load cases and boundary conditions for stresses and strains analysis of chassis using finite element analysis. King pin inclination, camber, caster, and toe-in angles of a truck’s wheels affect its chassis’ longitudinal and transverse stresses and strains. This work concentrates on studying the chassis’ stresses and strains when the truck is in longitudinal acceleration motion on asphalted straight road and has adjustable wheel angels for the steerable axles’ wheels.

Keywords: 8×4 trucks, king pin inclination, camber, caster, toe-in, truck dynamics, dynamic chassis stress and strain, finite element models and analysis

DOI 10.13140/RG.2.1.3829.3363

References

[1] Teo Han Fui, Roslan Abd. Rahman (2007) ‘Statics and Dynamics Structural Analysis of A 4.5 Ton Truck Chassis’, Jurnal Mekanikal, No. 24, PP. 56-67.

[2] Ashutosh Dubey and Vivek Dwivedi (2003) ‘Vehicle Chassis Analysis: Load Cases & Boundary Conditions for Stress Analysis’.

[3] Dheeraj S.and Sabarish R. (2014) ‘Analysis of Truck Chassis Frame Using FEM’, Middle-East Journal of Scientific Research 20(5), ISSN 1990-9233, PP. 656-661.

[4] Sani M. S. M., Arbain M. T. and et al (2009) ‘Stress Analysis and Modal Transient Response of Car Chassis’, International Conference on Advance Mechanical Engineering (ICAME09), 22-25 June 2009. Shah Alam, Selangor.

[5] Abdel-halim Nagwa A. (2015) ‘Reflection of Truck Loads Distribution Methods on the Truck Wheels Reaction Forces’, American Journal of Engineering, Technology and Society, Issue 4, Vol. 2, Pages 67-76.

[6] Abdel-halim Nagwa A., Abdel-hafiz Mohamed M. M. (2015) ‘Stress and Strain Analysis for a Ladder Truck Chassis’, American Journal of Engineering, Technology and Society, Issue 6, Vol. 2, Pages 131-139.

[7] Dana Spicer, (2007) ‘Steer Axles Application Guidelines”, AXAG0400, PP. 1-46.

[8] Prof. Dipl.-Ing. Jornsen Reimpell and Dipl.-Ing. Helmut Stoll (1996) ‘The Automotive Chassis: Engineering Principles, Types of drive and suspension, Tyres and wheels, Axle kinematics, steering, Springing, Chassis and vehicle overall’, English edition, Arnold London.

[9] van Berkum A. (2006) Chassis and suspension design FSRTE02, Unpublished Master’s Thesis, Technische Universiteit Eindhoven, Department of Mechanical Engineering, Section Dynamics and Control Technology.

[10] Artamonov M. D., Ilarionov V. A., and Morin M. M. (1976) ‘Motor Vehicles: Fundamentals and Design’, Mir bublishers Moscow.

[11] Wong J. Y.(1978) ‘Theory of Ground Vehicles’, A Wiley New York.

[12] Mehdi Mahmoodi-k, Iraj Davoodabadi, and et al (2014) ‘Stress and Dynamic Analysis of Optimized Trailer Chassis’, Technical Gazette 21, 3, PP. 599-608.

[13] Mitsubishi Fuso Truck & Bus Corporation (2009) Heavy Duty Fuso FS52JS4RFAB, Part No. TSH58A www.fuso.com.au

[14] Hutton David V. (2004) ‘Fundamentals of Finite Element Analysis’, McGraw New York.

[15] Mahvi Malik Shahzad, ShaikhRizwan, Tarique khan (2015) ‘Finite Element Static Structural Analysis of 4X2 Truck Chassis Frame’, International Journal of Modern Trends in Engineering and Research, e-ISSN No.:2349-9745, Issue 7, Vol. 2, PP. 1909-19014.

https://mmse.xyz/Papers/ID20160504.pdf

Creative Commons Licence

Mechanics, Materials Science & Engineering Journal by Magnolithe GmbH is licensed under a Creative Commons Attribution 4.0 International License.
Based on a work at www.mmse.xyz.