Effect of Alternating Bending and Texture on Anisotropic Damage and Mechanical Properties of Stainless Steel Sheets

<- Back to I. Materials Science Vol. 6

Cite the paper

V.V. Usov, N.M. Shkatulyak, E.A. Dragomeretskaya, E.S. Savchuk, D.V. Bargan & G.V. Daskalytsa. (2016). Effect of Alternating Bending and Texture on Anisotropic Damage and Mechanical Properties of Stainless Steel Sheets. Mechanics, Materials Science & Engineering Vol.6, pp. 56-63, doi: 10.13140/RG.2.2.35491.04640

Authors: V.V. Usov, N.M. Shkatulyak, E.A. Dragomeretskaya, E.S. Savchuk, D.V. Bargan, G.V. Daskalytsa

ABSTRACT. Effect of alternating bending and the crystallographic texture on the anisotropy of damage and mechanical properties of stainless steel sheets X5CrNi18-10 at subsequent uniaxial tensile tests were studied. The symmetric tensor of damage of the second order D was used for the analysis of anisotropy damage of sheet material. The only one non-zero component of this tensor D at uniaxial tensile was determined by the defect of the Young’s modulus from the mechanical test data. The value of D was found on relation . Here E0 and E are Young’s modules of the undamaged and tested material, respectively. It was established the anisotropy of the damage and mechanical properties of steel sheets at uniaxial tensile tests of initial sheet as well of sheets after alternating bending. This anisotropy is caused by the texture that is formed in sheets of investigated steel as was showed by correlation analysis.

Keywords: alternating bending, texture, Young’s modulus, anisotropy, damage, stainless steel

DOI 10.13140/RG.2.2.35491.04640

References

[1] “Most common uses of stainless steel” [Online]. Aviable: https://www.metalsupermarkets.com/most-common-uses-of-stainless-steel/

[2] “Role of Stainless Steel in Petroleum Refining (9021)”. [Online]. Aviable: https://www.nickelinstitute.org/~/media/Files/TechnicalLiterature/RoleofStainlessSteelinPetroleumRefining_9021_.ashx

[3] A. Chirkova, N. Makhutov, M. Gadenin, M. Kuzeev, V. Farkhutdinov, “A computational and experimental method for estimating degradation of mechanical characteristics of steels under the conditions of high-temperature pyrolysis”. Inorg Mater, vol. 46, pp. 1688–1691, 2010, DOI: 10.1134/S002016851015015X

[4] V. Mertinger, M. Benke, Sz. Szabo, O. Banhidi, B. Bollo, A. Kovacs, “Examination of a failure detected in the convection zone of a cracking furnace”. Engineering Failure Analysis, vol. 18, pp. 1675–1682, 2011, DOI: 10.1016/j.engfailanal.2011.02.003

[5] G. Hughes, Materials of crude oil Refining: corrosion Problems and prevention [Online]. Aviable: http://www.dunand.northwestern.edu/courses/Case%20study/Gareth%20Hughes%20-%20Materials%20of%20Crude%20Oil%20Refining.pdf

[6] I. Kucora, L. Radovanović, “Pyrolysis furnace tube damaging and inspection”. Acta tehnica corviniensis – Bulletin of Engineering, vol. 7, (3), pp. 19–24, 2014.

[7] V. Usov, E. Gopkalo, N. Shkatulyak, A. Gopkalo, T. Cherneva, “Texture, Microstructure, and Fractal Features of the Low Cycle Fatigue Failure of the Metal in Pipeline Welded Joints”. Russian Metallurgy (Metally), (9), pp. 759–770, 2015, DOI: 10.1134/S0036029515090128

[8] V. Usov, N. Shkatulyak, “Fractal nature of the brittle fracture surfaces of metal”, Materials Science, vol. 41, (1), pp. 62-66, 2005, DOI: 10.1007/s11003-005-0132-8

[9] N. Shkatulyak1, O. Tkachuk, “A role played by the crystallographic texture in the process of corrosion of hot-rolled rods made of carbon steel”. Materials Science, vol. 48, (2), pp. 153-161, 2012, DOI: 10.1007/s11003-012-9485-y.

[10] G. Gerstein, A.A. Bruchanov, D.V. Dyachok, F. Nürnberger, “The effect of texture in modelling deformation processes of bcc steel sheets”. Materials Letters, pp. 356-359, 2016, DOI: 10.1016/j.matlet.2015.11.007.

[11] S. Murakami, Continuum damage mechanics: A continuum mechanics approach to the analysis of damage and fracture, Springer Sciences + Business Media, Dordrecht, Heidelberg, London, New York, 2012. DOI 10.1007/978-97-007-2666-6_1

[12] V. Randle, O. Engler, Introduction to Texture Analysis: Macrotexture, Microtexture and Orientation Mapping, CRC PRESS, Boca Raton, London, New York, Washington, D.C., 2000.

[13] K. Rashid, Abu Al-Rub, G. Voyiadjis, “On the coupling of anisotropic damage and plasticity models for ductile materials”, International Journal of Solids and Structures, pp. 2611-2643, 2003, DOI: 10.1016/S0020-7683(03)00109-4

[14] M. Bobyr, O. Khalimon, O. Bondarets, “Phenomenological damage models of anisotropic structural materials”, Journal of mechanical engineering NTUU “Kyiv Polytechnic Institute”, pp. 5-13, 2013.

[15] E. Tadmor, N. Bernstein, “A First-Principles Measure for the Twinnability of FCC Metals”, J. Mech. Phys. Solids, vol. 52, pp. 2507-2519, 2004, DOI: 10.1016/j.jmps.2004.05.002

[16] N. Shkatulyak, “Effect of Stacking Fault Energy on the Mechanism of Texture Formation during Alternating Bending of FCC Metals and Alloys”. International Journal of Nonferrous Metallurgy, vol. 2, (2), pp. 35-40, 2013, DOI:10.4236/ijnm.2013.22005.

[17] Y. Vishnyakov, A. Babareko, S. Vladimirov and I. Egiz, Teoriya Obrazovaniya Tekstur v Metallakh i Splavakh (Theory of Textures Formation in Metals and Alloys), 1979, Nauka, Moscow, (russian).

[18] Springer Handbook of Metrology and Testing, Editors: H. Czichos, T. Saito, L. Smith, Springer Science & Business Media, 2011, DOI 10.1007/978-3-642-16641-9

https://mmse.xyz/Papers/ID201610061.pdf

Creative Commons Licence
Mechanics, Materials Science & Engineering Journal by Magnolithe GmbH is licensed under a Creative Commons Attribution 4.0 International License.
Based on a work at www.mmse.xyz.