Isothermal Pneumo-Forming of Hemispherical Parts Made Out of Anisotropic Materials In Short-Term Creep Mode

<- Back to I. Materials Science Vol.4

Cite the paper

Larin, S N; Platonov, V I; G.A., Nuzhdin

Isothermal Pneumo-Forming of Hemispherical Parts Made Out of Anisotropic Materials In Short-Term Creep Mode Journal Article

Mechanics, Materials Science & Engineering, 4 , pp. 34-45, 2017, ISSN: 2412-5954.

Abstract | Links | BibTeX

Authors: S.N. Larin, V.I. Platonov, Nuzhdin G.A.

ABSTRACT. Provided here are results of theoretical and experimental research of strained and stressed state, force modes, geometrical sizes for the blanks, and limit possibilities of deformation during isothermal blow molding of hemispheric parts of anisotropic material in creeping mode .Determined is the effect for the researched parameters of the studied deformation process, produced by anisotropy of mechanical properties, loading conditions and blank’s geometric dimensions. Comparison of the theoretical and experimental data regarding the relative blank thickness in the blank dome and base points, and of data regarding the relative height of the blank, point to their satisfactory agreement (up to 10 percent). Recommendations have been developed regarding calculation of scientifically-based technological parameters for operations of isothermal straining of semi-spherical components made out of highly strong anisotropic materials in the mode of short-time creeping. The recommendations were used during development of technological processes of manufacture — in the mode of short-time creeping and out of highly strong anisotropic materials –.of semispherical components conforming to the operational technical requirements. The technological processes provide for increasing specific strength by 1,5 – 1,7 times, for decreasing the mass by 1,5 times, for reducing labor content by 2-3 times, and for growth of capacity factor – from 0,3 to 0,9.

Keywords: anisotropy, mathematical model, high-strength materials, domed parts, pneumo-forming, creep, pressure, stress, thickness, damage rate, failure

DOI 10.13140/RG.2.1.3033.6408

References

[1] K.I .Romanov, Mechanics of hot metal forming, M .: Engineering, 1993. 240 pp.

[2] N.N. Malinin, Applied theory of plasticity and creep, M .: Mechanical engineering, 1975. 400 p.

[3] S.P. Yakovlev, V.N .Chudin, S.S .Yakovlev, J.A. Sobolev, Isothermal deformation of high anisotropic materials, M .: Engineering, 2004. 427 pp.

[4] S.S. Yakovlev, V.N. Chudin, J.A. Sobolev, S.P. Yakovlev, V.I. Tregubov, S.N. Larin, Isothermal pneumo-forming of anisotropic high-strength sheet materials, M .: Engineering, 2009. 352 pp.

[5] E.I. Semenov, Forging and Stamping: Reference: In 4 volumes. V.4. Stamping, M .: Engineering, 2010. 732 pp.

[6] Y.M.Aryshensky, F.V. Grechnikov, Theory and calculations of plastic deformation of anisotropic materials, M .: Metallurgy, 1990. 304 pp.

[7] F.V.Grechnikov, Straining of anisotropic materials, M .: Engineering, 1998. 446 pp.

[8] V.D. Golovlev, Calculation of stamping processes, M .: Engineering, 1974. 136 pp.

[9] S.P.Yakovlev, V.D. Kuhar, Punching anisotropic blanks, M .: Engineering, 1986. 136 pp.

[10] S,P.Yakovlev, S.S. Yakovlev , V.A. Andreichenko, Forming anisotropic materials, Kishinev: Quant, 1997. 332 p.10.

[11] S.S.Yakovlev, O.V. Pylypenko, Isothermal extract anisotropic materials, M .: Engineering, 2007. 212 pp.

[12] S.S.Yakovlev, V.I.Tregubov, Theory and technology of manufacturing large-sized axisymmetric critical parts of highly anisotropic materials, Tula: Tula State University Publishing House, 2011. 230 pp.

[13] S.S.Yakovlev, V.D.Kuhar, V.I.Tregubov, Theory and technology of forming anisotropic materials, M .: Engineering, 2012. 400 pp.

[14] S.S.Yakovlev, V.I.Tregubov , S.P.Yakovlev, Rotating hood with wall thinning rotationally symmetric parts of anisotropic round billets – specialized equipment, M .: Engineering, 2009. 265 pp.

[15] S.S.Yakovlev, V.I.Tregubov, Theory and technology of manufacturing large-sized axisymmetric critical parts of highly anisotropic materials, Tula: Tula State University Publishing House, 2011. 230 pp.

[16] S.S.Yakovlev, V.D.Kuhar, V.I.Tregubov, Theory and technology of forming anisotropic materials, M .: Engineering, 2012. 400 pp.

[17] S.S. Yakovlev, V.I.Tregubov, V.D .Kuhar, V.Y.Travin, Deep drawing of anisotropic materials, Tula: Tula State University Publishing House, 2013. 225 pp.

[18] S.S.Yakovlev, V.I.Tregubov, G.A.Nuzhdin, Plastic flow of anisotropic hardening material with strength differential effect, Tula: Tula State University Publishing House, 2014. 115 pp.

[19] S.S. Yakovlev, K.S. Belts, V.I.Tregubov, Stability of anisotropic sheet metal and of pipe blanks during plastic deformation, Tula: Tula State University Publishing House, RARAN, 2014. 222 pp.

 

For citation:

S.N. Larin, V.I. Platonov, G.A. Nuzhdin, Isothermal Pneumo-Forming of Hemispherical Parts Made Out of Anisotropic Materials In Short-Term Creep Mode, Mechanics, Materials Science & Engineering Journal, Magnolithe, 2016,[https://mmse.xyz/en/isothermal-pneumo-forming-of-hemispherical-parts-made-out-of-anisotropic-materials-in-short-term-creep-mode/]

Creative Commons Licence
Mechanics, Materials Science & Engineering Journal by Magnolithe GmbH is licensed under a Creative Commons Attribution 4.0 International License.
Based on a work at www.mmse.xyz.